sunxinzheng2008@163.com    +86-13713943531
enLanguage
Cont

Have any Questions?

+86-13713943531

Mar 25, 2022

​To improve the quality of plastic electroplating, the selection and design of plastic parts should also be paid attention to

To improve the quality of plastic electroplating, the selection and design of plastic parts should also be paid attention to


Plastic electroplating is an electroplating process developed with the continuous development of science and technology and the wide application of plastic products. It has been widely used in my country's electronics industry, national defense scientific research, household appliances, and daily necessities.


The application of the plastic electroplating process replaces the use of metal materials on the appearance of some products, saving a lot of metal materials. At the same time, its processing technology is relatively simple, and its own weight is lighter than metal materials. In this way, the plastic electroplating process is used. The weight of the equipment is also reduced, and the application of the plastic electroplating process makes the appearance of the plastic parts higher in mechanical strength, more beautiful, and durable.


Therefore, the quality of plastic electroplating is very important. There are many factors affecting the quality of plastic electroplating. The electroplating process, operation, and plastic process will have a greater impact on the quality of plastic electroplating. Therefore, specific measures should be taken according to different influences. Solutions to meet the quality requirements of plastic electroplating.


1 plastic parts selection


At present, there are many kinds of plastics on the market, but there are not many kinds of plastics that can be electroplated. Because each plastic has its own properties, it is necessary to consider the degree of bonding between the plastic and the metal layer and the physical properties of the plastic and the metal coating when electroplating. Similarly, if the difference is large, it is difficult to ensure its normal performance in the high-temperature environment of electroplating.


Currently on the market can be used for electroplating plastics such as ABS, followed by PP.


In addition, PSF, PC, etc. also have successful electroplating methods, but they are more difficult.


2 Plastic parts modeling design


In the electroplating process, the first consideration is the appearance and use-value. Under the premise of meeting these two preconditions, it is also necessary to meet the requirements of the plastic part shape as much as possible in the design.


1. The thickness of the plastic parts should be uniform to avoid shrinkage of the plastic parts due to unevenness. When the electroplating is completed, the metallic luster will also cause the shrinkage to be more obvious.


At the same time, the wall of the plastic product should not be too thin, otherwise, it will be easily deformed during electroplating, the bonding force of the coating will be poor, the rigidity will be reduced, and the coating will easily fall off during use.


2. Avoid blind holes, otherwise, the treatment solution remaining in the blind holes will not be easy to clean, which will cause contamination in the next process, thereby affecting the quality of electroplating.


3. The electroplating process has the phenomenon of sharp edge thickening.


If the plastic parts are sharp-edged during electroplating, it will be more difficult to electroplating. The sharp edge will not only cause power generation but also cause the edge coating to bulge. Therefore, when electroplating, try to choose a rounded transition with a radius of at least 0.3mm. above.


When electroplating flat plastic parts, try to change the plane to a slight arc shape or make it into a matte surface for electroplating because the flat plate will have a thin center and thick edges during electroplating.


At the same time, in order to increase the uniformity of the gloss of electroplating, the plastic parts with large electroplating surface area should be designed into a slightly parabolic shape as much as possible.


4. Minimize grooves and protrusions on plastic parts.


Because the deep concave parts are easy to be exposed during electroplating, and the protruding parts are easy to be scorched. The depth of the groove should not exceed 1, 3 of the groove width, and the bottom should be an arc. When there is a grid, the hole width should be equal to the beam width and less than 1/2 of the thickness.


5. Sufficient installation and hanging positions should be designed on the plated parts, and the contact surface with the hanging tool should be 2 to 3 times larger than that of the metal parts.


6. The plastic parts need to be electroplated in the mold and need to be demolded after electroplating. Therefore, it is necessary to ensure that the plastic parts can be easily demolded during the design, so as to avoid manipulating the surface of the plated parts or affecting the coating due to forcible removal from the mold. binding force.


7. When knurling is required, the knurling direction should be consistent with the demolding direction and in a straight line. The distance between the knurling stripe and the stripe should be as large as possible.


8. For plastic parts that need to be inlaid, because there is a certain degree of corrosiveness in the treatment before electroplating, the inlays should try to avoid using metal for inlays.


9. If the surface of the plastic part is too smooth, it is not conducive to the formation of the coating, because the surface of some plastic parts must have a certain surface roughness.


3 Mould Design and Manufacture


1. The mold material should not be made of beryllium bronze alloy. It should be made of high-quality vacuum cast steel. The surface of the cavity should be polished along the direction of the mold to be mirror bright, and the unevenness should be less than 0.21μm. The surface is preferably plated with hard chrome.


2. The surface of the plastic part faithfully reflects the surface of the mold cavity, so the mold cavity of the electroplated plastic part should be very smooth, and the surface roughness of the mold cavity should be 12 grades higher than the surface roughness of the part surface.


3. Parting surface, welding line, and core inlay line cannot be designed on the electroplating surface.


4. The gate should be designed at the thickest part of the part. In order to prevent the molten material from cooling too fast when filling the mold cavity, the gate should be as large as possible (about 10% larger than the ordinary injection mold).


5. There should be vent holes to avoid air filaments, air bubbles, and other defects on the surface of the workpiece.


6. When choosing the ejector mechanism, it should be ensured that the parts are demolded smoothly.


4 injection machine selection


In plastic electroplating, it is necessary to choose a suitable injection machine, because the pressure of the injection machine, the nozzle structure, and the internal stress generated by the mixing will have a certain impact on the bonding force of the coating.


Therefore, in order to ensure the fastening of the bonding force of the coating, it is necessary to choose the injection machine that is suitable for the specification and model.


5 Plastic molding process


Injection molding parts inevitably have internal stress due to the characteristics of the molding process, but proper control of the process conditions will minimize the internal stress of the plastic parts and ensure the normal use of the parts. The influencing factors of process conditions on internal stress mainly include the following situations:


1. Raw material drying


In the process of injection molding, if the raw materials used for electroplating parts are not dry enough, the surface of the parts will easily produce air filaments, air bubbles, etc., which will affect the appearance and bonding force of the coating.


2. Mold temperature


The temperature of the mold has a direct impact on the bonding force of the coating. When the temperature of the mold is high, the resin has good fluidity and the residual stress of the part is small, which is conducive to improving the bonding force of the coating, but it is not conducive to production when the mold temperature is too high. If the mold temperature is too low, it is easy to form two interlayers, so that the metal cannot be deposited during electroplating.


3. Processing temperature


The processing temperature is suitable. If the processing temperature is too high, it will cause uneven shrinkage, which will increase the volume temperature stress, and the sealing pressure will also increase. Therefore, the processing temperature can neither be too low nor too high. The nozzle temperature is lower than the maximum temperature of the barrel to prevent the plastic from casting. It is necessary to prevent the cold material from entering the mold cavity, so as to avoid defects such as lumps and stones in the parts, which will cause the coating to be not firmly bonded.


4. Injection speed, injection time, and injection pressure


If these three are not well mastered, the residual stress will increase, so the injection speed should be slow, the injection time should be shortened as much as possible, and the injection pressure should not be too large, which will effectively reduce the residual stress.


5. Cooling time


The cooling time should be controlled so that the residual stress in the cavity before mold opening is very low or close to zero. If the cooling time is too short, the forced molding will cause great internal stress to the part. However, the cooling time should not be too long, otherwise not only will the production efficiency be below, but also tensile stress will be generated between the inner and outer layers of the workpiece due to cooling shrinkage. These two extreme cases will reduce the coating adhesion of the plastic part.


6. Influence of release agent


It is best not to use a release agent for electroplated plastic parts. It is not allowed to use oil-based mold release agents, so as not to cause chemical changes in the surface of the plastic parts and change its chemical properties, resulting in poor coating bonding.


When a release agent is necessary, release only with talc or soapy water.


6 Influence of post-treatment of plastic parts on electroplating


Due to the different influencing factors of the plastic parts in the electroplating process, the internal stress of the plastic parts will be in different degrees, which will lead to a decrease in the bonding force of the coating.


At present, the method of heat treatment and treatment with surface finishing agents has a very good effect on eliminating the internal stress of plastic parts.


In addition, the plastic parts after electroplating need to be carefully packaged and inspected, and special packaging should be carried out to avoid damaging the appearance of the electroplated parts.


Send Inquiry