The conditions and equipment required for electrolytic polishing
Using microscopic bumps on the metal surface in a specific electrolyte and an appropriate current density. An electrolytic process in which polishing is performed on the principle of anodic dissolution first. Also known as electropolishing, English abbreviation ECP.
This processing method was invented by P.A. Jacques of France in 1931 and was used in the industry shortly after.
01 Overview
The workpiece is connected to the positive pole of the DC power supply as the anode.
Use lead, stainless steel, and other conductive materials resistant to electrolyte corrosion as the cathode, and connect to the negative electrode of the DC power supply. The two are immersed in the electrolyte (usually based on sulfuric acid and phosphoric acid) at a certain distance, and under a certain temperature, voltage and current density (generally lower than 1A/cm2), energized for a certain period of time (generally tens of seconds to a bit).
The tiny bumps on the workpiece surface are the first to dissolve. It gradually becomes a smooth and shiny surface.
The characteristics of electropolishing are:
①The polished surface will not produce a metamorphic layer, no additional stress, and can remove or reduce the original stress layer;
② It can process hard materials, soft materials, thin-walled, complex shapes, and small parts and products that are difficult to be mechanically polish;
③The polishing time is short, and multiple pieces can be polished at the same time, so the production efficiency is high;
④ The surface roughness that can be achieved by electropolishing is related to the original surface roughness.
Generally, it can be increased by two levels. However, due to the poor versatility of the electrolyte, short service life, and strong corrosiveness, the application range of electropolishing is limited.
Electrolytic polishing is mainly used for metal products and parts with small surface roughness, such as mirrors, stainless steel tableware, decorations, injection needles, springs, blades, and stainless steel pipes, etc. It can also be used for some molds (such as bakelite molds and glass molds, etc. ) and metallographic polishing.
02 Electrolytic polishing process
Degreasing--washing--rust removal--washing--electropolishing--washing--neutralization--washing--passivation--packaging
03 Advantages of electropolishing
Advantages of electropolishing:
⑴The inner and outer color is consistent, the luster is durable, and the recesses that cannot be thrown by mechanical polishing can also be leveled.
⑵ high production efficiency and low cost.
(3) Increase the corrosion resistance of the workpiece surface.
04 Conditions and equipment required for electrochemical polishing
(1) Power supply:
The power supply can be selected from two-phase 220V and three-phase 380V.
(2) Rectifier
Electrolytic polishing is not too strict on the power supply waveform, and silicon-controlled rectifiers and high-frequency rectifiers can be selected.
Rectifier no-load voltage: 0—20v
Load voltage (working voltage): 8—10v
The working voltage is lower than 6v, the polishing speed is slow, and the brightness is insufficient.
Rectifier current: according to the size of the customer's workpiece.
(3) Electrolyzer and supporting facilities (anode rod)
It can be welded by PVC hard plate. Three electrode rods are installed on the tank, the middle is a movable anode rod, which is connected to the anode (or positive pole) of the power supply, and the two sides are cathode rods, which are connected to the cathode (negative pole) of the power supply.
(4) Heating facilities and cooling equipment
①Heating can choose quartz heating tube, titanium heating tube.
②Coil can be used for cooling, which can be heated or cooled.
(5) Fixtures
It is best to use titanium as the hanger, because titanium is more corrosion-resistant and has a long service life, and titanium ions have no effect on the bath. It is recommended not to use copper hangers because the entry of copper ions will deposit a copper layer with poor bonding force on the surface of stainless steel, which will affect the polishing quality. The exposed parts of copper can be baked with polyvinyl chloride glue to form a film, and the insulating film can be scraped off at the contact point.
(6) Cathode and anode materials
The cathode and anode rods should be made of copper rods or copper tubes. The length of the copper tube should be the length of the electrolytic cell plus 20 cm. The cathode plate should be a lead plate. The lead plate should be fixed on the cathode rod. The length of the lead plate should be the height of the tank plus 10 cm. The length depends, generally 10 cm, 20 cm specifications.
At present, electrolytic polishing is mainly aimed at the surface brightening of stainless steel workpieces. Stainless steel workpieces are divided into 200 series, 300 series, and 400 series materials, and each series of materials must use the targeted electrolytic polishing liquid.
For example, stainless steel of 200 series stainless steel must use the 200 series formula, which cannot be adapted to 300 series or 400 series stainless steel. This has always been a major problem in China because some manufacturers' materials are composite workpieces, both 200 series stainless steel and 300 or 400 series stainless steel.
The workpiece is put into a specific solution for anodic electrolysis, the process of smoothing the metal surface and producing metallic luster is called electropolishing.
When electropolishing, the workpiece is connected to the anode. When energized, a thick mucous membrane with high resistivity will be produced on the surface of the workpiece, and its thickness is not uniform on the surface of the workpiece. The microscopic protruding part of the surface is thinner, the current density is larger, and the metal dissolves faster; the microscopic concave part of the surface is thicker, the current density is smaller, and the metal dissolution is slower.
Due to the non-uniformity of the thick mucous membrane and the current density distribution, the size of the microscopic convex parts decreases rapidly, and the size of the microscopic concave parts decreases slowly, which reduces the surface roughness of the workpiece, thereby achieving the purpose of polishing.






