Hydrogen embrittlement is a phenomenon of delayed fracture that occurs when hydrogen penetrates into the metal and causes damage, which causes the metal material to undergo a static stress lower than the yield strength of the material.
Hydrogen embrittlement is a common phenomenon in engineering, especially in the production process of electroplating, it is very easy to cause hydrogen embrittlement of metal materials. Hydrogen embrittlement in the electroplating process mainly occurs in pickling, electroplating and other processes.
Therefore, after electroplating, many parts will undergo dehydrogenation treatment to avoid the hazards caused by hydrogen embrittlement. The following editor will introduce the method of removing hydrogen.
1 General method of hydrogen removal
(1) Put the parts to be de-hydrogenated in an oven (preferably in a vacuum furnace), or in hot oil (suitable for hard chrome plating), and treat them at 200~250℃ for more than 3H.
(2) The removal of hydrogen from hot oil has the same effect as the removal of hydrogen in an oven. Because of its uniform heating, it also has the effect of filling pores in the coating, which is beneficial to improve the protective function of the coating and has simple equipment requirements.
2 According to the requirements of the workpiece, the method of hydrogen removal is proposed
For example, in hard chromium plating, the current efficiency is only 13%~18% during hard chromium plating. Most of the current is consumed on the precipitation of hydrogen. Hydrogen easily diffuses into the plating layer and the crystal lattice of the base metal, and hydrogen permeation is more serious. , Resulting in a reduction in fatigue strength, affecting dynamic and static load strength, so the design should put forward the requirements of hydrogen removal after chromium plating. After the hydrogen removal treatment, 60% to 70% of the hydrogen that penetrates into the coating and the matrix can be removed, thereby greatly reducing the brittleness without reducing its hardness.
3Hot oil instead of removing in the oven
The current efficiency of chromium plating is very low, so the porosity of the plating layer is high, and the plating layer is very easy to passivation. At the same time, because the chromium layer on the surface of steel parts has the advantage of cathodic plating, when the thickness of the plating layer is thin, it is easy to cause rust. In order to improve this defect link, hot oil hydrogen removal can be used to replace the hydrogen removal process in the oven under the same process conditions. Practice has proved that this process method can not only keep the temperature of each part of the workpiece uniform, and achieve a complete hydrogen removal effect, but also can effectively fill the pores and cracks of the chromium layer with grease, thereby improving the protective ability of the chromium layer.
4 The temperature of hydrogen removal should not be too high
For example, after zinc plating, hydrogen is removed from the metal by heating. The effect of hydrogen removal is related to the temperature of hydrogen removal and the length of holding time. The higher the temperature of hydrogen removal and the longer the time, the more thorough the removal of hydrogen. But it cannot exceed 250 degrees Celsius. Because at this temperature, the crystalline structure of the galvanized layer will be deformed, brittle, and corrosion resistant.
Pay attention to the following points when removing hydrogen:
(1) Use safety factor of parts. For parts that are of great importance to safety, the hydrogen removal time should be appropriately extended.
(2) The geometric shape and cross-sectional area of the part. Small and thin parts with notches and small angles that are prone to stress concentration should be strengthened to remove hydrogen.
(3) The degree of hydrogen penetration of the parts. For parts that produce a lot of hydrogen during surface treatment and have a long treatment time, hydrogen removal should be strengthened.
(4) The nature of the force in use of the part. When the parts are subjected to high tensile stress, the hydrogen removal should be strengthened, and hydrogen embrittlement will not occur when only the compressive stress is applied.
(5) The surface of the coating must be kept clean before hydrogen removal. The hydrogen removal should be treated before passivation to ensure the hydrogen removal effect and the quality of the passivation layer.
(6) Dehydrogenation should ensure that the time is continuous and cannot be stopped in the middle. When possible, wait for the oven to drop to room temperature before opening the oven to take out the parts.
(7) Try not to rework parts after plating. If electroplating is unavoidable, alkaline solution can be used to remove the plating layer, and the hydrogen removal time can be extended after electroplating.
(8) The hydrogen removal treatment should be carried out within 3 hours after electroplating.







