Electroplating sludge refers to the heavy metal-containing sludge waste produced after wastewater treatment in the electroplating industry, which is included in the seventeenth category of hazardous waste in the national hazardous waste list. As the "final state" of electroplating wastewater, although its amount is much smaller than that of wastewater, the heavy metals such as cu, Ni, cr, zn, Fe in wastewater are transferred to sludge, in a sense, Electroplating heavy metal sludge is more harmful to the environment than electroplating wastewater. If this extremely harmful electroplating sludge is not disposed of, the damage to the ecological environment is self-evident. On the other hand, if the extremely high-grade heavy metal substances in the electroplating sludge are not recycled, It also means a huge waste of resources. Therefore, for the harmless disposal and comprehensive utilization of electroplating heavy metal sludge, scholars at home and abroad have done a lot of research work in this area and have achieved many phased results. This article summarizes the various technologies of harmlessness and resource utilization of electroplating sludge, learns from others, and finally finds a treatment method with strong adaptability and can completely solve the problem of electroplating sludge.
1 Characteristics and hazards of electroplating sludge
Most electroplating wastewater treatment methods produce sludge, and chemical precipitation is the main source of sludge. Some methods, such as ion exchange method and activated carbon method, do not directly produce sludge, but in some auxiliary links of the method, such as the treatment of regenerated liquid, sludge is also produced. As chemical method is used as a main treatment method at home and abroad, the situation of electroplating sludge is very serious. According to the different treatment methods of electroplating wastewater, electroplating sludge can be divided into two categories: mixed sludge and elemental sludge. The former is the sludge formed by mixing different types of electroplating wastewater for treatment; the latter is the sludge formed by treating different types of electroplating wastewater separately, such as chromium-containing sludge, copper-containing sludge, and nickel-containing sludge. Sludge, zinc-containing sludge, etc. However, in fact, most small electroplating companies get mixed sludge after treatment. Therefore, the current treatment and resource utilization of electroplating sludge are also mainly targeted at mixed sludge.
The sludge produced in the process of electroplating wastewater treatment contains harmful heavy metals. It has the characteristics of easy accumulation, instability, and easy loss. If it is not properly treated and stacked arbitrarily, the direct consequences are cu, Ni, zn, and cr in the sludge. Wait for these heavy metals to be leached by rain. It will migrate along the path of sludge-soil-crop-human body, and may cause secondary pollution of surface water, soil, and groundwater, and even endanger the biological chain, causing serious environmental damage.
Aiming at the characteristics and hazards of electroplating sludge. From the perspective of environmental pollution prevention and resource recycling, the following two treatment methods are mainly adopted. One is to discard and store the sludge without causing secondary pollution after treatment; The heavy metal resources in the sludge are comprehensively recovered, that is, resource utilization.
2 Harmless disposal of electroplating heavy metal sludge
The harmless technology of sludge treatment and disposal is a prerequisite for the realization of sludge resource utilization. In the "Technical Policy for Pollution Prevention and Control of Hazardous Wastes" (Huanfa [2001] No. 199) issued on December 17, 2001, China requires that by 2015, hazardous wastes in all cities should be basically treated and disposed of in an environmentally sound manner.
2.1 Curing agent curing
Among the many treatment methods of hazardous solid waste, solidification technology is an important technology in the treatment of hazardous waste, and it occupies an important position in the regional centralized management system. Compared with other treatment methods, it has the advantages of easy availability of curing materials, good treatment effect and low cost. The curing process is a process in which additives are used to change the engineering properties of the waste (such as permeability, compressibility, strength, etc.). In recent years, the United States, Japan and some European countries have generally adopted solidification treatment technology for toxic solid waste, and believe that this is a final disposal method that converts hazardous materials into non-hazardous materials. The solidified materials used include cement, lime, and glass. And thermoplastic materials, etc. Among them, cement curing is the most commonly used curing technology at home and abroad. It is considered a very promising technology in the United States. It has been proven to be very effective for the fixation of some heavy metals. The US Environmental Protection Agency has also confirmed that it has a good effect on eliminating the sludge produced by some special plants. Jia Jinping conducted a series of experimental studies on the basis of summarizing the research experience of ARoy et al. on cement-solidified electroplating sludge, and found that the addition of _ren 425 cement to the electroplating heavy metal sludge is based on concrete and sludge. The curing test is carried out at 40:1 or 50:1, and the strength (28d) of the obtained sample can reach the standard of No. 275 cement. The cured body has a good curing effect on zn, cu, Ni, and cr ions. Through further research, it is found that the electroplating sludge is ferriteized and pre-cured, and then cured with the concrete in a ratio of 1:30. The leaching solution was analyzed, and it was found that this method has better curing and stabilizing effects on zn, Ni, Cu, and Cr, and the strength of the product can reach the cement standard of No. 325. Wu Shaolin and others used electroplating chromium sludge as the object, cement as curing agent, thiourea and sodium silicate as additives, and studied the leaching law of chromium in water with different additive dosages, ratios and different pH values. The experimental results show that the cement curing effect is good, (cement): (chrome mud) is 1.5:1. Adding thiourea, sodium silicate and other additives can reduce the leaching concentration of chromium. The stabilizing effect of thiourea is better than sodium silicate. There is a certain synergistic effect between the two, and sodium silicate can significantly increase the strength of the solidified block. Tu Jie, etc. use HAS soil curing agent instead of cement to solidify electroplating sludge, which can obtain slope protection bricks with good leaching resistance, corrosion resistance, permeability resistance, and sufficient mechanical strength. The solidification process opens up a new way for resource utilization of electroplating sludge.
2.2 Landfill
From the perspective of economy, technology, and waste status, landfill technology is a harmless disposal method for hazardous waste that is more suitable for China’s national conditions. However, the domestic landfill technology for electroplating sludge and other hazardous wastes is still at a relatively low level. . Because most of the industrial hazardous wastes are simply stacked or landfilled, the damage to the environment is quite serious, especially the problem of groundwater pollution. However, the technical obstacles are of a limited duration. At present and in the near future, landfill is still necessary. Special emphasis is placed on the safe landfill of hazardous wastes, that is, pre-treatment must be carried out to stabilize them before landfilling to reduce potential hazards caused by toxicity or solubility. In recent years, the state has gradually improved the management and disposal of hazardous wastes such as electroplating sludge. In 1995, the first hazardous waste landfill meeting international standards was built in Shenzhen, Guangdong. In 2001, the state promulgated the "Hazardous Waste Landfill Pollution Control Standard" (GB18598-2001), which truly achieved no impact on electroplating sludge. A good foundation has been laid for the disposal of hazardous chemicals.
2.3 Throwing into the sea
Throwing into the sea is actually a transfer of pollutants. By choosing a disposal site with a suitable distance and depth, the electroplating sludge can be dumped into the ocean, a big receptor. Disposal to the sea was once also an important method of sludge disposal. For example, the United States used to dispose of various wastes including electroplating heavy metal sludge from 1899 to 1965. Among the European Union countries, the United Kingdom, Ireland, etc. 25% to 45% of the solid waste is treated by throwing into the sea. However, the obviously toxic sludge must be solidified before being allowed to enter the ocean. Regardless of whether it is cast directly into the sea or cast into the sea after solidification, the threats it poses to the marine ecosystem and human health are inevitable. Therefore, international conventions have explicitly banned them, and direct pollutants to the sea are not allowed to be discharged after 1998.
2.4 Incineration heat treatment
Sludge incineration uses high temperature to completely oxidize and decompose the organic matter in the sludge, so as to minimize the toxicity of some highly toxic components in the sludge. Through incineration heat treatment, the volume of electroplating sludge can be greatly reduced, and the harm to the environment can be reduced. In addition, the products of incineration have utility value. For example, the ash can be used for making bricks, paving or other purposes, and the heat generated by incineration can be used for power generation. Therefore, the incineration heat treatment is a fast and effective technology to realize the reduction and harmlessness of electroplating sludge. In recent years, some scholars have conducted extensive research on the resource utilization of incineration slag on the basis of incineration volume reduction. Liao Changhua and others have used electroplating heavy metal sludge containing low concentrations of Cu and Ni as the research object. Pretreatment increases the content of heavy metals in the sludge, thereby creating conditions for the final leaching of valuable metals to prepare sponge copper and nickel sulfate products.
However, due to the high energy consumption of this method, there are certain requirements for incineration equipment and conditions, and ordinary small electroplating plants cannot bear the huge processing costs, so it is difficult to get large-scale promotion.
3 Comprehensive utilization of resources of electroplating heavy metal sludge
Due to the depletion of resources and the aggravation of environmental pollution, electroplating sludge as an important heavy metal resource to be recycled has always been the focus of research at home and abroad. Industrialized countries have generally paid attention to the development of new technologies for recovering heavy metals from electroplating sludge in the 1970s and 1980s. During the "Seventh Five-Year Plan" and the "Eighth Five-Year Plan" period, China also specially set up research topics on the resource utilization of electroplating sludge. As a cheap secondary resource, as long as proper treatment methods are adopted, electroplating sludge can turn waste into treasure, bringing considerable economic and environmental benefits. With the rapid development of economy and society, the resource utilization of electroplating sludge will gradually become a promising green industry.
3.1 Recycling of heavy metals
3.1.1 The leaching-precipitation method selectively leaches the electroplating sludge to dissolve the heavy metals in groups. This is a key step in the recovery of heavy metals and also the key to determining the subsequent metal recovery rate. The leaching and dissolution of metals mainly include acid leaching and ammonia leaching. At present, there is a preference for ammonia leaching with relatively good selectivity in the world. Since the precipitation method separates and recovers heavy metals in the leachate, the process is simple and the application is relatively wide. Researchers from Czech u- proposed a multi-stage precipitation process for treating nickel electroplating sludge and conducted research in the laboratory. This technology includes sludge acid leaching and various precipitation methods to purify sulfate leaching solution, so that impurities coexisting in nickel electroplating sludge, such as Fe, zn, cu, cr, Cd, A1, etc., are removed, and the final stage of precipitation Nickel is separated from the purification solution in the form of hydroxide. The purity achieved by the final nickel precipitate is sufficient for direct reuse in the metallurgical industry. Mao Zizhang et al. studied the process route of sulfide precipitation, separation and purification, sodium chlorate sulfuric acid system leaching and recovery of copper, and the total recovery rate of copper reached 94.5%. Chen Fanzhi and others researched the use of leaching at room temperature, iron filings replacement, multi-step precipitation purification to prepare nickel sulfate and solidification treatment process to comprehensively utilize electroplating sludge. Industrial pure nickel sulfate can be obtained, and the nickel recovery rate is greater than 80%.
3.1.2 Leach-solvent extraction method
The solvent extraction method of electroplating sludge is to add an organic solvent complementary and compatible with water or an organic solvent containing an extractant into the leaching solution. Through the mass transfer process, some heavy metal substances in the sludge enter the organic phase to achieve The purpose of separation and concentration is also called liquid-liquid extraction. In the 1970s, the Swedish National Technical Development Committee supported Chalmers University to develop the Am-MAR "leaching-solvent extraction" process to recover heavy metals such as cu, zn, and Ni in electroplating sludge, and gradually formed an industrial scale. China’s Zhu Wanpeng and others have conducted a series of experimental studies on the recovery of valuable metals from electroplating sludge based on the solvent extraction process. The metal salt crystallization process is used to recover valuable metals from electroplating sludge, and various high-purity metal salt products containing Cu, zn, Ni, cr, etc. are obtained. Later, a four-stage countercurrent extraction of N, kerosene and HsO was used. The process can make the extraction rate of copper reach 99%, while the loss of coexisting nickel and zinc is almost zero. Copper is recovered in the form of copper salt CuSO·5H:O or electrolytic high-purity copper during this process. Preliminary economic analysis It shows that its output value offsets the daily operating costs and has higher economic benefits. The entire process is simple, cyclically operated, and basically does not produce secondary pollution. Later, after process improvements, the team studied the sulfuric acid leaching-P shan~ The kerosene-sulfuric acid system extracts and separates iron and sodium soap-P:. A kerosene-sulfuric acid system co-extracts chromium and aluminum-back-extracts separation of chromium and aluminum process to recover metals in the ammonia leaching residue of electroplating sludge. Through optimization experiments, and The optimal process parameters of the whole process were determined. The results showed that the metallic chromium, aluminum and iron in the iron-chromium slag can be recovered in the form of high-purity salts, and can be used as chemical reagents with a recovery rate of over 95%. Portugal’s J. E. Silva et al. studied the process of electroplating sludge containing heavy metals such as cu, cr, zn, Ni, etc., using sulfuric acid leaching, displacement removal, precipitation removal, chromium removal, D2EHPA and Cyancx272 extraction and separation of zinc and nickel, and a crystallization process. The results showed that. The extraction rate of zinc by D2EHPA is higher than that of Cyncx272, and all the zinc in the organic phase can be recovered. After crystallization, nickel sulfate products with fairly high purity can be obtained. In the removal stage of copper and chromium, copper recovery The rate reaches 90%, and the produced Cr-CaCO precipitates, and it is possible to make silicate materials. For details, please refer to http://www.dowater.com for more related technical documents.
3.1.3 Electrolysis
According to the basic principles of electrolysis in physical chemistry, some domestic smelters have carried out electrolytic treatment on the sludge mainly containing Fe(OH) and Cr(OH) components. Among them, the method of Wuhan Smelter is worth learning. They added a certain amount of water and sulfuric acid to the sludge. After boiling for 30 minutes, the filtered filtrate was transferred to the freezing tank, and then added ammonium sulfate of 1 to 2.5 times the theoretical amount to convert the formation of chromium sulfate and iron sulfate. It is iron alum, which can separate chromium and iron according to the solubility of chromium alum and iron alum at low temperature (75°C). Finally, more than 90% of chromium can be recovered.
3.1.4 Hydrogen reduction separation method Hydrogen reduction separation of metal substances is a relatively mature technology.
Since the 1950s, hydrogen has been used to reduce the production of metals such as copper, nickel and cobalt in industry, and significant economic and social benefits have been achieved. Zhang Guandong and so on? Wet hydrogen reduction was used to comprehensively recover valuable metals such as cu, Ni, and zn in the ammonia leaching product of electroplating sludge, and successfully separated metallic copper powder and nickel powder. The experimental results show that in the weakly acidic ammonium sulfate solution, a better separation effect of copper and nickel can be obtained. The purity of the obtained two metal powders can reach 99.5%, which meets the product requirements of 3 copper powder and 3 nickel powder, the recovery rate of copper reaches 99%, and the recovery rate of nickel reaches more than 98%. And on this basis, the zinc in the reduction tail liquid was recovered. The method has simple process, low investment and high product purity, and is worthy of further improvement and promotion in industrial production.
3.1.5 Calcined acid solution method Jitka Jandova et al. ¨ passed
Experimental studies have found that it is a simple and feasible method to acid-dissolve, calcinate, re-acid-dissolve copper-containing electroplating sludge, and finally recover it in the form of copper salt. In the high-temperature calcination process, most of the impurities, such as Fe, Zn, Al, Ni, si, etc. are transformed into slow-dissolving oxides, so that the copper can be separated in the next process, and finally cu(SO)H:0 In the form of recycling. This method has a simple process, no need to add other reagents, and has strong economy and simplicity. However, the recovered copper salt contains many impurities, and the process needs to be further optimized.
3.2 Comprehensive utilization technology of ferrite
Ferrite technology is developed based on the principle of ferrite production. The application of ferrite comprehensive utilization technology to dispose of electroplating heavy metal sludge and make it into suitable industrial products is a method that has been affirmed after many scholars' experimental research. . Since electroplating sludge is the product of electroplating wastewater flocculated by ferrous iron, electroplating sludge generally contains a large amount of iron ions, especially in Cr-containing electroplating sludge, it can be turned into composite ferrite by using appropriate inorganic synthesis technology. , The iron ions in the electroplating sludge and many other metal ions are bound to the iron tetroxide lattice points of the inverse spinel face-centered cubic structure, and the crystal structure is stable, which achieves the purpose of eliminating secondary pollution.
Ferriteization is divided into two processes: dry process and wet process. Jia Jinping of Shanghai Jiaotong University uses electroplating sludge produced by Shanghai Electric Machinery Plant and Shanghai Pump Plant as raw materials to synthesize iron black products through wet process. Iron black pigments are used as raw materials, and many products have been developed, such as C43—31 black alkyd paint, Y53—4-2 iron black oily anti-rust paint and so on. Subsequently, a new process of dry reduction and drying after electroplating sludge wet synthesis of ferrite was developed on the original basis, and a patent was applied for. This process can synthesize magnetic flaw detection powder with excellent performance, and has the advantages of simple process, high yield, no secondary pollution, and low processing cost.
3.3 Composting to make fertilizer
The main method of controlling heavy metal pollution in sludge at home and abroad is to use sludge composting. Composting is the process of artificially controlling the conversion of organic matter into fertilizer through microbial fermentation under certain moisture, C/N and ventilation conditions.
Many microorganisms in nature have the ability to oxidize and decompose organic matter. Practice has proved that microorganisms can be used to biochemically degrade organic matter under certain humidity and pH conditions to form substances similar to humus, which can be used as fertilizer and soil improvement. There are different requirements for the aerobic composting and anaerobic composting. Composting increases the temperature, speeds up its decomposition, and kills pathogenic bacteria. The research on the composting treatment of electroplating sludge is still in the exploratory stage. Zhou Jianhong and others composted the chromium-containing sludge after the treatment of electroplating waste chromium solution. After 24 days, the content of chromium (VI) in 1g of sludge can be reduced by The original 4.060mg was reduced to 0.028mg, which solidified most of the heavy metals and greatly reduced their toxicity. After composting, the pot experiment of applying the sludge to flowers showed a better growth response and avoided the human food chain, opening up a new way for the treatment and resource utilization of chromium-containing sludge. Researcher at Shanghai Jiaotong University. . The ferrite synthesized from electroplating sludge is magnetized and made into magnetic fertilizer. The application research has been carried out in the field. The results found that the application of this kind of magnetic fertilizer has a significant effect on increasing the yield of chickens, green onions and other crops, and shortens the growth cycle. . However, electroplating sludge in China generally has high heavy metals content and complex composition. The use of composting sludge for agricultural use still has certain difficulties and risks. In addition, the long composting cycle and complicated procedures also limit the research on the composting treatment of electroplating sludge. .
3.4 Production of modified plastic products
The joint production of modified plastic products by electroplating sludge and waste plastics is an original new technology in China, jointly developed by many scientific research units in Shanghai. The basic principle is to use the method of plastic solidification, using electroplating sludge as a filler, mixing with waste plastics at an appropriate temperature, and forming modified plastic products through processes such as pressing, injection molding, and molding. After electroplating sludge is dried at a high temperature of 400-600℃ in a special TGZS300 high-humidity material dryer, the heavy metals are basically stable, and the leaching test meets the national standard. Studies have shown that the unmodified electroplating sludge and plastic are physically mixed, so they are encapsulated solidification. However, after modification with a surfactant (such as sodium oleate), the X-ray powder diffraction pattern analysis shows that it has a significant chemical effect and improves the hydrophobicity of the sludge, with a contact angle of 100. Therefore, it can be inferred that it has better compatibility with plastics, uniform filling, and improved mechanical properties. The plastic products produced by this process (including modified and dried electroplating sludge), through leaching tests show that the leaching rate of heavy metals and the mechanical strength of the plastic products can reach the specified indicators.
Electroplating sludge and waste plastics are combined to produce modified plastic products, which not only solves the safe disposal of waste materials, but also makes full use of waste resources. It is an important way to turn waste into treasure, comprehensive utilization, and realize waste recycling. It has a good society and Environmental benefits.
4 Conclusion
The electroplating industry is one of the three major polluting industries in the world today. Facing the gradual fragility of the ecological environment and the increasingly scarce resources of the world, it is of great significance to actively carry out the harmless disposal and comprehensive utilization of electroplating sludge, and it is also an inevitable choice for the realization of sustainable social development.






