sunxinzheng2008@163.com    +86-13713943531
enLanguage
Cont

Have any Questions?

+86-13713943531

Jan 07, 2025

Single metal plating-Zinc plating

Plastic plating-Single metal plating-Zinc plating

Huizhou City Boluo Tenglong Technology Co., Ltd. wholeheartedly serves you! Mainly engaged in plastic water electroplating processing, accompanying plastic injection molding processing, mold processing and so on!

The appearance of the zinc coating is bluish-white. The relative atomic mass of zinc is 65.38, the density is 7.178/g/cm3, and the melting point is 420°C. The standard electrode potential of zinc is-0.76V. It is easily soluble in acid and alkali. The electroplated zinc layer has high purity, relatively uniform structure, and almost no chemical changes occur in dry air. The critical humidity of zinc corrosion is greater than 70%, so it can react with carbon dioxide and oxygen in humid air to form a thin film composed of basic zinc carbonate. This film has a certain corrosion inhibition effect.

The total amount of galvanizing accounts for about 60% of the total amount of galvanizing. Anti-corrosion is the most important technical property of zinc coating. Zinc coating is the most important, economical and simple means to prevent steel from being corroded. The standard electrode potential of zinc is more negative than that of iron and is generally used as an anodic coating of steel and iron products. In an electrochemical corrosion environment, when the zinc coating is damaged, because the potential of zinc is more negative than that of iron, zinc is dissolved first as the anode, and the base metal iron is protected as a cathode. Compared with other metals, zinc is a relatively cheap and easy to plate. It is a low-value anti-corrosion plating layer. It is widely used to protect steel parts, especially to prevent atmospheric corrosion, and can also be used for decorative coatings. Zinc coating can be used as a protective layer for steel products used in the industrial atmosphere, rural atmosphere and marine atmosphere. The protective life is basically proportional to the thickness of the zinc layer. In the atmosphere polluted by industrial waste gas and fuel waste gas, the zinc coating will have strong corrosion resistance. After passivation, the corrosion resistance of the zinc coating can be improved by 5 to 8 times.

Research on zinc plating additives initially started from acidic plating solutions. In 1907, R.C.Snowden discovered that formaldehyde in acidic electrolytes could reduce the size of zinc coating grains. In 1908, E.C. Broadwell invented a zinc plating bath composed of zinc sulfate and zinc naphthalene disulfonate, which is considered to be the first successful zinc plating bath. However, the uniformity of the plating solution is poor, and the parts must be thoroughly cleaned before electroplating. In 1916, cyanide zinc plating began to be used for electroplating press-forged castings. Since cyanide zinc plating can still obtain good and uniform coatings without additives, it was first promoted and used on a large scale. In 1921, W.Blum developed an additive-free alkaline cyanide zinc plating process, which has little change from the composition of the high-cyanide plating bath used today. Subsequently, some additives began to be introduced and developed rapidly. It has gradually developed from thiourea, furfural, animal glue, etc. to polymer additives such as polyvinyl alcohol. Since 1940, many inorganic metal ions and organic additives have been used as brighteners and leveling agents to achieve a stable, wide current density, and low-cost zinc plating process. The most eye-catching ones are synthetic organic compounds, such as polymers formed by polyamines and nitrogen-containing heterocyclic compounds. They not only can obtain extremely bright coatings within a wide current density in cyanide plating baths, but also are suitable for low, medium and non-cyanide zinc plating baths, becoming the most widely used type of additive in the industry to date. During this period, the development of acid zinc plating also continued, and many additives were constantly being tested to bring it closer to cyanide zinc plating. For example, substances such as pyridine, thiourea, and licorice are added to sulfate zinc plating baths to improve their homogeneity and brightness.

Before the 1970s, the zinc plating electrolyte was mainly cyanide zinc plating, accounting for about 95%. In the late 1960s, due to the strengthening of environmental awareness, chloride and alkaline cyanide-free zinc plating began to be promoted. The earliest acid chloride zinc plating process was born in the Federal Republic of Germany in 1963, mainly to solve the wastewater treatment of cyanide zinc plating. Alkaline cyanide-free zinc plating is a polyethyleneimine that is quaternized in zincate solutions. In the 1970s, cyanide zinc plating accounted for 93%, non-cyanide alkaline zinc plating accounted for 4%, and chloride zinc plating accounted for 3%. Due to the continuous improvement of the cyanide-free zinc plating process and the further strengthening of environmental awareness, the cyanide-free zinc plating process has developed rapidly. The original chloride zinc plating was a plating bath of ammonium chloride and chelating agents, but with the introduction of acid potassium salt zinc plating and the development of high-performance surfactants, acid chloride zinc plating has developed rapidly (from 1980 to 1990, especially its unique conductivity, high efficiency and brightness make it one of the most widely used types. As an early alternative to cyanide zinc plating process, chloride zinc plating could not achieve the effect of cyanide zinc plating, and its leveling ability was poor. Alkaline cyanide-free zinc plating has also been developed due to its proprietary high dispersion ability and other properties. Especially in recent years, due to the introduction of new intermediates and the improvement of alkaline zinc plating processes, the coating and plating have been greatly improved. The performance of the plating solution makes it close to or even exceed cyanide zinc plating in some aspects. However, today, acid chloride zinc plating still has the largest share in various zinc plating baths. By the 1990s, foreign cyanide zinc plating accounted for only 20%, alkaline non-cyanide zinc plating accounted for 30%, and chloride zinc plating accounted for 50%. Moreover, the proportion of cyanide-free zinc plating is further increasing, and cyanide zinc plating is gradually developing in the direction of medium, low and even micro-cyanide.

Zinc plating solutions are divided into alkaline plating solutions, acidic plating solutions, neutral plating solutions and weak acid plating solutions. Alkaline plating solutions include cyanide plating solutions, alkaline zincate plating solutions, pyrophosphate plating solutions, etc.; acidic plating solutions include sulfate plating solutions, ammonium chloride plating solutions, etc.; neutral and weak acid plating solutions include chloride plating solutions, etc. Although there are dozens of zinc electroplating processes that have emerged after continuous research and development by electroplating personnel, not many are truly practical. Currently, the most common ones are the following.

1)cyanide zinc plating

Cyanide zinc plating is the most mature and oldest process. It uses cyanide with strong coordination ability and good surface activity as the ligand for zinc ions, making cyanide zinc plating the best zinc plating process currently recognized.

2)alkaline zincate zinc plating

In 1936, E.Mantgell first began to use alkaline zincate zinc plating. This plating bath has good current efficiency and dispersion ability, but the coating is spongy and has no practical value. In the early 1970s, a process with DE or DPE as the main additive and some auxiliary additives made cyanide-free alkaline zincate zinc plating possible. DE or DPE additives, dimethylamine and epichlorohydrin respectively

Send Inquiry