How to perform chemical nickel plating and precautions
Chemical Plating
Chemical plating plays an important role in surface treatment technology. Chemical plating is a chemical treatment method that uses a suitable reducing agent to selectively reduce and precipitate metal ions in a solution on the catalyst-activated surface into a metallic coating. It can be expressed by the following equation.
M2++2e (provided by the reducing agent) ---> M
In chemical plating, the metal ions within the solution are dependent on getting the required electrons to be reduced to the corresponding metal. For example, if hypophosphite is used as a reducing agent in an acidic chemical nickel plating solution, it has the following redox reaction process.
Ni2++2e--->Ni(reduction)
(H2PO2)-+H2O-->(H2PO3)-+2e+2H+(oxidation)
The two equations are added together to obtain the full reduction-oxidation reaction
Ni2++(H2PO2)-+H2O-->(H2PO3)--+Ni+2H+
The effective degree of the reducing agent can be inferred from its standard oxidation potential. From the above, it is clear that hypophosphite is a strong reducing agent and can produce a positive value of the standard oxidation-reduction potential. However, the E° value should not be overly relied upon, because in practical applications, the E° value can vary greatly due to the activity of different ions in solution, overpotential, and similar factors. Still, the calculation of oxidation and reduction potentials can help to estimate in advance the effective degree of different reducing agents. If the full standard redox potential is too small or negative, the metal reduction will be difficult to occur.
The composition of the electroplating solution and its corresponding working conditions must be such that the reaction is restricted to the surface of the part with a catalytic effect, and the solution itself should not undergo reduction and oxidation spontaneously, lest the solution decomposes naturally and cause the solution to failing quickly. If the metal to be plated (such as nickel, palladium) itself is the catalyst of the reaction, the process of chemical plating has an automatic catalytic effect, so that the above reaction is carried out continuously, at which time the thickness of the plating also gradually increases and a certain thickness is obtained. In addition to nickel, cobalt, rhodium, palladium, etc. are all autocatalytic.
For non-metals such as plastics, glass, ceramics, etc., which do not have the autocatalytic surface, special pretreatment is usually required to activate the surface and make it catalytic before chemical plating can be performed.
Compared with electroplating, electroplating has the following advantages.
①No additional DC power supply equipment is required.
②Dense plating with less porosity.
③No influence of the uneven distribution of power lines, and it is possible to obtain a uniform thickness of plating layer for plated parts with complicated geometry;
④Can be plated on various substrates such as metals, non-metals, and semiconductors.
Compared with electroplating, the solution used is less stable, the maintenance, adjustment, and regeneration of the solution are more troublesome, and the material cost is higher.
The electroplating process has an important place in the electronics industry. Because of the different types of reducing agents used, there are significant differences in the performance of the layer obtained by chemical plating, therefore, when selecting the formulation of the plating solution, the economy of the plating solution and the characteristics of the resulting layer should be carefully considered.
At present, chemical plating of nickel, copper, silver, gold, cobalt, palladium, platinum, tin, as well as chemical alloy plating, and chemical composite plating, has been adopted in industrial production.
How to perform chemical nickel plating
Chemical nickel plating is the most widely used method of chemical plating, the reducing agents used are hypophosphite, hydrazine, sodium borohydride, dimethylamine borane, etc...
At present, most of the domestic production of sodium hypophosphite as a reducing agent, sodium borohydride, and dimethylamine borane because of the more expensive, only a small amount of used.
1. The use of the plating layer
Electroless nickel plating layer has meticulous crystallization, low porosity, high hardness, uniform plating, good weldability, good deep plating ability of plating solution, high chemical stability, and has been widely used in electronics, aviation, aerospace, machinery, precision instruments, daily-use hardware, electrical appliances, and chemical industry.
The application of chemical nickel plating on non-metallic materials is increasing, especially plastic products that can be plated with the required metal layer by the conventional plating method after chemical nickel plating to obtain the same appearance as metal. Plastic plating products have been widely used in electronic components, household appliances, daily-use industrial products, etc.
Electroless nickel plating has been used in the atomic energy industry, such as in the production of parts and containers in nuclear fuel systems and parts for rockets, missiles, jet engines.
Chemical equipment in the compressor and other parts for anti-corrosion, anti-wear, and the use of a chemical nickel plating layer is very beneficial.
A Chemical nickel plating layer can also improve the welding performance of aluminum, copper, stainless steel materials, reduce the wear of the rotating part, reduce the stress corrosion of stainless steel and titanium alloy.
Plating size requirements for precise precision parts and geometry of complex parts of deep holes, blind holes, cavities of the inner surface, with chemical nickel plating can get the same thickness as the outer surface of the coating.
For the parts requiring high hardness and wear resistance, chemical nickel plating can be used instead of hard chrome plating.






