sunxinzheng2008@163.com    +86-13713943531
enLanguage
Cont

Have any Questions?

+86-13713943531

Apr 01, 2022

Classification of electroplating layers

Classification of electroplating layers


 There are various ways of classifying electroplating layers. They can be classified according to the purpose of the coating, according to the electrochemical relationship between the coating and the substrate during the corrosion of the metal, or according to the structure of the coating.

According to the purpose of the coating, they can be roughly divided into two categories: protective and decorative coatings and functional coatings.


Coatings that protect products from corrosion and give them a certain lustrous appearance that lasts for a long time are used a lot in production and life and are typical of protective and decorative coatings. Most of these coatings are made up of a combination of multiple layers, i.e. first a "base" layer on the substrate, then a "surface" layer, and sometimes an "intermediate" layer. This is so because it is difficult to find - a single - metal plating that meets both the protection and decoration requirements. Some plated metals are highly resistant to corrosion, but they do not retain their luster under service conditions and are often soft and easily worn. Some plated metals are less resistant to corrosion, but they give a pleasing luster to the exterior of the product and are less prone to wear, and this lustrous appearance can be maintained over time under service conditions. Therefore, their respective strengths have been identified and utilized to make up for their respective shortcomings by using a combination of them, thus. The result is a multi-layer protective and decorative coating that is both corrosion resistant and aesthetically pleasing. For example, the exterior of common cars, bicycles, motorcycles, clocks, and watches.


Motorbikes, watches, and other products with exposed parts of the luster coating, all belong to this category. At present, most of the domestic use of Cu / Ni / Cr or Ni / Ni / Cr and other combinations of plating. Among these coatings, galvanized coatings, which are mainly intended to protect steel materials from atmospheric corrosion, are the most widely used. In marine climates, cadmium plating is usually chosen. Considering the seriousness of cadmium pollution to the environment, zinc-based alloys have been used instead of cadmium plating in recent years. For ferrous metal products that come into contact with organic acids (e.g. food containers), tin plating should be used. Layer, it is not only strong anti-corrosion ability, and the resulting corrosion products are harmless to humans. In addition, there are a number of plating layers that are used.


The aim is to focus on their decorative qualities, such as imitation gold plating. Functional plating is the use of various mechanical, physical and chemical properties of the plated metal to meet the needs of various occasions, according to the performance of the plating, they can also be divided into the following main categories.


A. Wear-resistant and wear-reducing coatings


Wear-resistant plating mainly relies on improving the surface hardness of products to increase their resistance to wear and is mostly used in industry for hard chrome platings, such as the journals of various shafts and crankshafts, the roller surfaces of printing rollers, the cylinder walls and piston rings of engines, and the inner cavities of stamping dies. Wear reduction plating is mostly used for sliding contact surfaces. A layer of ductile metal (wear-reducing alloy), which acts as a solid lubricant, is plated on these contact surfaces to reduce sliding friction. This kind of plating is mostly used in shaft tiles and bushings, such as tin plating, Sn- Pb alloy, Sn- Pb- Sb ternary alloy, etc.


Second, anti-high temperature oxidation plating


Many technical departments wide] need to use high melting point metal materials to manufacture special-purpose parts, but these materials may be oxidized at high temperatures (high-temperature corrosion), and make zero, parts damage. To solve this problem, the surface of the parts can be plated, high a temperature antioxidant layer. For example, the inner cavity of the rotor engine needs to be protected by chrome plating, and the rotor blades of the jet engine can also be coated with chrome alloy. In special cases, even Pt-Rh alloy coating can be used as a high-temperature antioxidant layer.


Third, conductive plating


In the electronics industry, there is a need to use a large number of plating layers that can improve the electrical conductivity of the surface. In general, can be plated with copper or silver plating. Both require good electrical conductivity, but also have certain wear resistance, should be plated with Ag - Sb, Ag - Ni, Au - Sb, Au - Co alloy, etc... Silver and La203 particles such as the formation of composite coatings have a strong resistance to galvanic corrosion, they can be used to replace the overall pure silver preparation of electrical contacts, used in switches, relays, and other devices. In addition, in the production of high-frequency waveguides, most of the silver plating layer with mirror luster is used.


Four, magnetic plating


In electronic computer equipment, magnetic rings, magnetic drums, disks, magnetic film, and other storage components, are required to use magnetic materials.


At present, the plating method is mostly used to form the plating layer to meet the requirements of this area. By changing the plating process parameters, the magnetic properties of the plating can also be adjusted. Commonly used electrodeposited magnetic alloys are Ni- Fe, FeNi, Co-Ni, and Co- Ni-P.


V. Plating for heat treatment


In order to improve the surface physical properties of mechanical parts, heat treatment is often required. However, if some parts of the parts, in the heat treatment do not allow it to change their original performance, it is necessary to protect this part locally. For example, to prevent local carburization needs to be plated copper, to prevent local nitriding should be plated tin.


Six, restorative plating


Some important mechanical parts, such as a variety of shafts, splines, gears, pressure rollers, etc., in the use of the process, were worn, or in the process of excessive grinding, can be used to repair the plating method, so that it can function again. Can be used to repair the size of the plating metal are copper, iron, chromium, etc.


VII. Solderable plating


Some electronic components need to be brazed when assembled. In order to improve their solderability, they need to be plated with tin, silver, or Sn- Pb alloy, etc.


Eight, another functional plating


There are many other functional coatings used in production practice. For example, in order to enhance the adhesion of steel wire and rubber hot pressing, can be plated on the wire brass (Cu- Zn alloy); in order to resist the corrosion of sulfuric acid and chromic acid, can be plated aluminum; in order to increase the reflective ability, can be plated with chromium, silver or high tin bronze; in order to matte or absorb light energy into heat, can be plated with black nickel, black chromium, etc...


Send Inquiry