Plastic plating-the basic knowledge of electroplating.
Huizhou Boluo Tenglong Technology Co., Ltd. serves you wholeheartedly! Mainly engaged in plastic hydroelectroplating processing, with plastic injection molding processing, mold processing and so on!
Electroplating definition: electroplating is the abbreviation of electrolytic metal plating. Electroplating is a method in which the plated parts (products) are immersed in a potion containing metal ions to be plated and connected to the cathode, and a proper anode (soluble or insoluble) is placed at the other end of the potion. After direct current is applied, a layer of metal film is precipitated on the surface of the plated parts.
Five basic elements of electroplating:
1. Cathode: plated, refers to all kinds of connector terminals.
two.. Anode: if it is a soluble anode, it is to be metallized. If insoluble anodes, most of them are precious metals (platinum, iridium oxide).
3. Electroplating potion: an electroplating potion containing metal ions to be plated.
4. Electroplating bath: a bath that can bear and store electroplating solution, generally considering factors such as strength, corrosion resistance, temperature resistance and so on.
5. Rectifier: a device that provides DC power.
Electroplating purpose: electroplating not only requires beauty, but also has different purposes according to all kinds of electroplating needs.
1. Copper plating: used as a base to improve the adhesion and corrosion resistance of electroplated coating.
two.. Nickel plating: used as a base to improve corrosion resistance.
3. Gold plating: improve conductive contact impedance and enhance signal transmission.
4. Palladium and nickel plating: improve conductive contact impedance, enhance signal transmission, wear resistance is better than gold.
5. Tinned lead: improve welding ability and will soon be replaced by other substitutes.
Electroplating process: general copper alloy substrate is as follows (not including washing project).
1. Degreasing: alkaline preparation and electrolytic degreasing are usually used at the same time.
two.. Activation: use dilute sulfuric acid or related mixed acid.
3. Nickel plating: use nickel sulfate system and nickel aminosulfonate system.
4. Palladium and nickel plating: all of them are ammonia at present.
5. Gold plating: there are gold and cobalt, gold and nickel, gold and iron, generally use gold and cobalt system most.
6. Tin plated lead: alkyl sulfonic acid system.
7. Drying: use hot air circulation to dry.
8. Sealing treatment: there are two kinds of water-soluble and solvent-based.
Composition of electroplating solution.
1. Pure water: the total impurity should be at least lower than 5ppm.
two.. Metal salts: provide metal ions to be plated.
3. Anodic dissociation auxiliaries: increase and balance anodic dissociation rate.
4. Conductive salt: improve the electrical conductivity of the potion.
5. Additives: buffer, gloss agent, smoothing agent, softener, wetting agent, inhibitor.
Electroplating conditions:
1. Current density: the current per unit plating area, usually the higher the current density, the thicker the film, but if it is too high, the coating will be scorched and dry.
two.. Electroplating position: the position of the plating part in the solution, relative to the anode, will affect the film thickness distribution.
3. Stirring condition: the better the stirring effect is, the higher the electroplating efficiency is. There are air, water flow, cathode swing and other stirring methods.
4. Current waveform: in general, the better the filter, the more uniform the coating structure.
5. The bath temperature is about 50: 60 for gold plating, 50: 60 for nickel plating, 18: 22 for tin and lead plating, 45: 55 for palladium and nickel plating.
6 the PH value of plating bath is about 4.0 ~ 4.8 for gold plating, 3.8 ~ 4.4 for nickel plating, and 8.0 ~ 8.5 for palladium and nickel plating.
7. The specific gravity of the plating bath is basically low, the conductivity of the solution is poor, and the electroplating efficiency is poor.
Plating thickness: at present, the electroplating thickness of electronic connector terminals is expressed as a. μ ``. Microinch, b. μ m, micron, 1 μ m equals about 40 μ m.
1.Tin-Lead Alloy Plating: tin-lead alloy electroplating.
For welding purposes, the film thickness is generally between 100 and 150 μ ``at most.
2.Nickel Plating nickel plating.
At present, electronic connectors are all based on underplating, so more than 50 μ ``is the general specification, while the lower specification is 30 μ`` (may take into account bending or cost).
3.Gold Plating gold plating.
For expensive electroplating processing, when selecting specifications, the general electronic industry must take into account its practical environment, object of use and manufacturing cost. If it needs to pass the general strong corrosion test, it must be above 50 μ.
Coating inspection:
1. Appearance inspection: visual method, magnifying glass (4x 10x).
two.. Film thickness test: X-RAY fluorescent film thickness meter.
3. Adhesion experiment: bending method, tape method or both.
4. Soldering experiment: tin dipping method, generally more than 95% of the tin area can be uniform and smooth.
5. Steam aging test: test for discoloration or corrosion spots and subsequent weldability.
6. Anti-discoloration test: use the oven baking method, whether discoloration or peeling.
7. Corrosion resistance test: salt water spray test, nitric acid test, sulfur dioxide test, hydrogen sulfide test, etc
Jan 24, 2024
Plastic Plating-the Basic Knowledge Of Electroplating
Send Inquiry
Product Categories
Latest Products






