sunxinzheng2008@163.com    +86-13713943531
enLanguage
Cont

Have any Questions?

+86-13713943531

Apr 13, 2022

PCB Nickel Plating Process and Troubleshooting

PCB Nickel Plating Process and Troubleshooting


1. Function and characteristics


PCB (the abbreviation of PrintedCircuieBoard printed circuit board in English) uses nickel plating as the substrate coating of precious metals and base metals and is also commonly used as a surface layer for some single-sided printed circuit boards. For some surfaces that are heavily worn, such as switch contacts, contacts, or plug gold, using nickel as a backing layer of gold can greatly improve wear resistance. When used as a barrier, nickel is effective in preventing diffusion between copper and other metals. Dumb nickel/gold combination coatings are often used as etching-resistant metal coatings, and can meet the requirements of hot-press welding and brazing. Only nickel can be used as a corrosion-resistant coating for ammonia-based etchants without hot-press welding. PCBs with bright plating are also required, usually with bright nickel/gold plating. Nickel plating thickness is generally not less than 2.5 microns, usually 4-5 microns.


PCB low-stress nickel deposits are usually plated with modified Watts nickel baths and some nickel sulfamate baths with stress-reducing additives.


We often say that PCB nickel plating includes bright nickel and matt nickel (also known as low-stress nickel or semi-bright nickel), which usually require uniform and meticulous plating, low porosity, and low stress and good ductility.


2. Nickel sulfamate (ammonia nickel)


Nickel sulfamate is widely used as a substrate coating on metalized hole plating and printed plug contacts. The obtained deposited layer has low internal stress, high hardness and excellent ductility. Add a stress reliever to the bath and the resulting coating will be slightly stressed. There are a variety of sulfamate baths with different formulations. The typical nickel sulfamate bath formula is shown in the table below. Due to the low stress of the coating, it is widely used, but the stability of nickel sulfamate is poor, and its cost is relatively high.


3. Modified Watt Nickel (Sulfur Nickel)


Modified Watts Nickel formulation using nickel sulfate, along with the addition of nickel bromide or nickel chloride. Due to internal stress, nickel bromide is mostly used. It can produce a semi-bright, slightly internal stress, good ductility coating; and this coating is easy to activate for subsequent electroplating, and the cost is relatively low.


4. The role of each component of the plating solution:


Main salts—nickel sulfamate and nickel sulfate are the main salts in the nickel solution. The nickel salts mainly provide the nickel-metal ions required for nickel plating and also play the role of conductive salts. The concentration of nickel plating solution varies slightly with different suppliers, and the allowable content of nickel salt varies greatly. The high content of nickel salt allows the use of high cathode current density and fast deposition and is often used for high-speed thick nickel plating. However, if the concentration is too high, the cathodic polarization will be reduced, the dispersion ability will be poor, and the carry-out loss of the plating solution will be large. Low nickel salt content has a low deposition rate, but has a good dispersing ability, and can obtain fine crystal and bright coating.


Buffering agent—boric acid is used as a buffering agent to maintain the pH value of the nickel plating solution within a certain range. The practice has proved that when the PH value of the nickel plating solution is too low, the cathode current efficiency will decrease; when the PH value is too high, the PH value of the liquid layer close to the cathode surface will increase rapidly due to the continuous precipitation of H2, resulting in Ni The formation of (OH)2 colloid and the inclusion of Ni(OH)2 in the coating increase the brittleness of the coating. At the same time, the adsorption of Ni(OH)2 colloid on the electrode surface will also cause hydrogen bubbles to stay on the electrode surface. The porosity of the coating increases. Not only does boric acid have a pH buffering effect, but it can increase cathodic polarization, thereby improving both performance and reducing "burning" at high current densities. The presence of boric acid is also beneficial to improve the mechanical properties of the coating.


Anode activator—except for sulfate-type nickel plating solutions that use insoluble anodes, other types of nickel-plating processes use soluble anodes. The nickel anode is easily passivated during the electrification process. In order to ensure the normal dissolution of the anode, a certain amount of anode activator is added to the plating solution. Through experiments, it is found that the CI-chloride ion is the best nickel anode activator. In the nickel plating solution containing nickel chloride, in addition to being the main salt and conductive salt, nickel chloride also acts as an anode activator. In the electroplating nickel solution that does not contain nickel chloride or its content is low, a certain amount of sodium chloride should be added according to the actual situation. Nickel bromide or nickel chloride is also commonly used as a stress reliever to maintain the internal stress of the coating and give the coating a semi-bright appearance.


Send Inquiry