sunxinzheng2008@163.com    +86-13713943531
enLanguage
Cont

Have any Questions?

+86-13713943531

Sep 07, 2023

Detection Technology Of Non-metallic Materials For Automobile

Glue plating-the latest technology: detection technology of non-metallic materials for automobile.
Huizhou Boluo Tenglong Technology Co., Ltd. serves you wholeheartedly! Mainly engaged in plastic hydroelectroplating processing, with plastic injection molding processing, mold processing and so on!
The properties and processing technology of non-metallic materials are changing with each passing day, which makes them used in automobiles at an unprecedented speed. The average consumption of non-metallic materials per car has increased from 68.4 kg in 1981 to 150-180 kg at present. At the same time, the market has put forward higher requirements for the testing of the corresponding

O1CN01dkD6Zg2DWdfAtPkaq2208782778617-0-cib

performance of such materials, such as the impact of the condensation of volatile materials on the windshield on the driver's safety and the air permeability of the plastic fuel tank. the barrier of inner tube, airbag and so on. In view of these problems, the corresponding testing methods, testing standards and testing instruments have been introduced and improved one after another.
Atomization detection of interior parts.
Automobile interior decoration materials, such as engineering plastics, textiles, leather, nonwovens, etc., as well as various adhesives used to install these materials, their volatile components will evaporate under the action of high temperature. and form condensation on the car window or windshield, causing the driver to have a bad line of sight and seriously affect driving safety. At present, this aspect has been tested abroad, and the relevant testing standards followed are IN 75201, ISO 6452, SAE J1756 and so on. Some domestic automobile and interior parts manufacturing enterprises have paid enough attention to the relevant testing either in order to improve product quality or to open up overseas markets.

t01c2f1df37fdfb3b64
There are two test methods for atomization detection of interior parts: glossiness test method and weight test method. The former is to measure the atomization characteristics of the tested sample by the change of the glossiness of the glass plate before and after atomization, while the latter is to get the quality of the atomized condensate through the change of the quality of aluminum foil before and after atomization. In addition, the "fog value" or "atomization-condensate quality" obtained through the test can also quantitatively determine the volatilization of toxic and harmful substances in the sample; by testing the atomization value of the xenon lamp in front of the car, it can also test to what extent the atomization of the headlights will affect the illuminance.
At present, the atomization testing equipment sold in the Chinese market are German Huck, China Jinan Languang and other brands.
Testing of air permeability and moisture permeability of seat materials.

t01ed5301fa3c9f65c8
During the long journey, drivers often have to sit in the car for several or even dozens of hours, so the air permeability and moisture permeability of car seat materials are higher than those in other places. Good cushions and chairs should be soft and flexible, and have good air permeability and moisture permeability, so that the sweat of drivers can be discharged smoothly and make people feel comfortable.

t0187c2e40f1b080c09
The testing method of air permeability is as follows: a sample of a specified size is placed in the test chamber and emptied on one side of the sample to form a certain pressure difference between the two sides of the sample, and under this pressure difference, the flow rate of gas through the given area of the sample is measured within a certain period of time. Calculate the air permeability; or maintain the flow through the sample, measure the pressure difference on both sides of the sample, and calculate the air flow resistance. The test method follows GB/T10655-2003.
The testing method of moisture permeability is as follows: the sample is sandwiched between the dry and wet cavity at a constant temperature, the sensor located in the test cavity analyzes the change of humidity in the cavity, and tracks the time required from the preset lower limit to the upper limit, through continuous measurement and systematic analysis, the moisture permeability and coefficient of the sample are obtained. The test method follows ASTM E398.
Measurement of air permeability of plastic fuel tank.

t01ea877389ade45126
At present, the utilization rate of plastic fuel tanks of Chinese cars has reached 86%. Compared with the steel plate fuel tank, the automobile plastic fuel tank has the characteristics of safety, corrosion resistance, long service life, random modeling and low production cost. However, the barrier performance of the automobile plastic fuel tank is poor, which will cause the penetration and volatilization of the fuel, so it is necessary to test its barrier performance in order to select the ideal material.
The traditional test method is as follows: after injecting the quantitative gasoline into the fuel tank, sealing and weighing the fuel tank to get its quality M1, after putting it for enough time (usually more than 100days), weighing again to get its quality M2, calculating M=M1-M2, M is the volatilization of fuel. This method requires a long testing time and requires high-precision weighing tools, so it is difficult to realize.
ASTM D3985 gives another test method. Cut the plastic sheet of the fuel tank, measure the oxygen permeability of the sheet, and compare the oxygen permeability of all kinds of plastic sheet, so as to scientifically and quickly find out which kind of plastic has better barrier property and is more suitable for making fuel tank. ASTM F1307 gives the test method of the whole container, thus realizing the test of the tightness of the whole fuel tank.
Gas barrier detection of inner tube and airbag.
The materials for the manufacture of automobile inner tube and airbag require good barrier, the former ensures that the car runs for a long time without inflation, while the latter ensures that it can be bulged quickly at the moment of accident collision to ensure a certain degree of pressure.

t0186564cce8f5d2ee3
The traditional detection method is to inflate the finished inner tube or airbag to a certain pressure, record the pressure gauge value at this time, and observe the pressure drop of the pressure gauge value after a period of time, so as to obtain its barrier performance. This kind of detection method usually takes a long time to get results (sometimes more than a year), which is difficult to implement. Now the VAC- V1 gas permeometer produced by Jinan Languang Mechanical and Electrical Technology Co., Ltd. can be used to sample the tested material and clamp it on the instrument, so that a constant pressure difference can be maintained on both sides of the sample, and the pressure change with time after gas permeation through the sample can be measured, thus the barrier performance of the material can be obtained. The test on this instrument can generally be completed within 12 hours, which greatly improves the work efficiency.
Detection of other non-metallic materials.

t03c1fb49978ab3161a
There are a lot of non-metallic materials used in cars, and the same material has different performance requirements in different parts, so it is necessary to carry out various items of testing. Such as tensile strength, tear strength, hardness, bending strength, color, friction coefficient and so on.
In addition, a variety of adhesives are widely used in the car, and the performance of the adhesive has a vital impact on the quality of the whole vehicle, so it is necessary to test the properties of this kind of non-metallic materials, such as shear, tension, pull-off and so on.

 

Send Inquiry