sunxinzheng2008@163.com    +86-13713943531
enLanguage
Cont

Have any Questions?

+86-13713943531

Mar 13, 2024

Classification and process description of plastic electroplating-electroplating process

Classification and process description of plastic electroplating-electroplating process.
Huizhou Boluo Tenglong Technology Co., Ltd. serves you wholeheartedly! Mainly engaged in plastic hydroelectroplating processing, with plastic injection molding processing, mold processing and so on!
Electroplating process is widely used in various fields of national production, only careful operation can effectively save energy and protect the environment. Here is a brief introduction to some basic knowledge about electroplating process. Classification of electroplating process: acid bright copper plating nickel / gold tin plating.
Technological process: pickling "full plate electroplating copper" acid deoiling "micro-etching" pickling "tin plating" pattern copper plating "nickel plating" citric acid gold plating.
Process description.
(1) pickling.
1 function and purpose: remove the oxides on the plate surface and activate the plate surface, the general concentration is about 5%-10%, mainly to prevent the unstable sulfuric acid content of the trough liquid caused by the introduction of water.
(2) when using C.P grade sulfuric acid, the acid leaching time should not be too long to prevent plate oxidation; after a period of use, the acid solution should be replaced in time when the acid solution is turbid or the copper content is too high, so as to prevent the surface of electroplated copper cylinder and plate from being polluted.
(2) full plate copper plating.
1 function and purpose: to protect the thin chemical copper just deposited from being eroded by acid, and to add it to a certain extent by electroplating.
2 process parameters related to copper plating on the full plate: the bath solution is mainly composed of copper sulfate and sulfuric acid, and the formula of high acid and low copper is adopted to ensure the uniformity of plate thickness distribution and the ability of deep hole deep plating during electroplating; the sulfuric acid content is mostly between 180 and 240 grams / liter; the content of copper sulfate is generally about 75 grams / liter, and there can be trace chloride ions in the bath solution, which can play a glossy effect as an auxiliary gloss agent and copper gloss agent. The addition of copper gloss agent in 3~5ml/L, the addition of copper gloss agent is generally added according to the method of kiloampere-hour or according to the actual production plate effect; the current of full-plate plating is generally calculated by 2 A / square decimeter multiplied by the plating area on the board; the temperature of copper cylinder is generally controlled at 22 degrees Celsius.
3 process maintenance: replenish the copper gloss agent timely according to 1000 ampere hours every day; check whether the filter pump is working properly; scrub the cathode conductive pole with a clean wet dishcloth every 2-3 hours; regularly analyze and adjust the light content through Hall cell test every week; clean the anode conductive pole and the electric joint at both ends of the cell body every week to replenish the anode copper ball in the titanium basket. Every month, the titanium basket bag of the anode should be checked for damage and replaced in time; and whether there is anode mud accumulated at the bottom of the anode titanium basket should be checked every month; the need for large treatment should be decided according to the pollution of the bath liquid every half a year or so; and the filter element of the filter pump should be replaced every two weeks.
(4) the anode copper ball contains a small amount of phosphorus in order to reduce the anodic dissolution efficiency and reduce the production of copper powder.
(5) when replenishing drugs, if the amount of copper sulfate or sulfuric acid is higher than that of copper sulfate or sulfuric acid, it should be added slowly for several times; otherwise, the temperature of the bath will be too high, the decomposition of the photoagent will be accelerated, and the bath will be polluted.
(3) acid deoiling.
1 purpose and function: remove the oxide on the copper surface of the line and ensure the binding force between primary copper and pattern plating copper or nickel.
(2) when using acid deoiling agent, it is only necessary to control the concentration and time of deoiling agent in production.
(4) microerosion.
1 purpose and function: clean and roughen the copper surface of the line to ensure the binding force between pattern electroplating copper and primary copper.
(2) Sodium persulfate was used as microetching agent.
(5) pickling.
1 function and purpose: remove the oxides on the plate surface and prevent the unstable sulfuric acid content in the trough liquid caused by the introduction of water.
(2) to use C.P grade sulfuric acid leaching time should not be too long to prevent oxidation.
(6) graphic copper plating, also known as secondary copper.
Purpose and function: in order to meet the rated current load of each line, each line and hole copper needs to reach a certain thickness, line copper plating is to thicken the hole copper and line copper to a certain thickness.
(7) Electroplating tin.

Send Inquiry